How To Solder A Toilet Shut Off Valve

Using the existing pipe that sticks out of the wall remove current valve then attach some elbowbend to it. Disassemble the shutoff valveleaving the toilet and supply lines intact.

How To Replace This Push Pull Shutoff Terry Love Plumbing Advice Remodel Diy Professional Forum

If you unsolder them take great care to remove all the old solder and cleansmooth the pipe end well before attempting to solder a new valve.

How to solder a toilet shut off valve. Clean the washers with a cloth. Assuming they are solder on you must heat them to melt the solder and remove them or cut them free with a tubing cutter as close to the existing valve as possible. Learn how easy it is.

Valve is connected to. Place a bucket under the old valve. Use the rag to wipe away excess solder.

The goal is to cool things down quickly. I need to move the water supply valve. Just bought a new house.

Water supply valve is almost dead center with toiletflange making installation of new toilet difficult if not impossible. They also help isolate and repair leaks nea. You need to tighten the inlet of the toilet line in the shutoff valve.

Determining if your water shut off valve is a solder or compression union will not involve a complicated home-improvement algorithm but rather one simple step. Use a dry cloth to wipe the piping. The one in your first post that shows the older valve is the same one a plumber installed replacing the plastic valve shut off I had.

Start by disconnecting the water line from the valve. I noticed that some of the solder had formed as a drip at the bottom of the pipe. Make sure to shut off the main water supply before doing this repairDo it yourself replacement of a faulty shut off valve to a toilet.

The plumber was here to cap my bathroom sink lines charging me 219. Two types of valves exist. Removal methods vary according to valve type.

I did get the toilet shutoff to work by using WD-40 and turning the valve. One day the toilet continued to run even though everything inside looked okay. I tried to shutoff the water at the toilet before I left the house but it wouldnt turn off all the way.

I heated up the solder and took and old screw driver and scraped off the liquid solder. Dont use any pipe dope or plastic tape on the valve. Next remove the old compression sleeve and nut.

Avoid gumming up the inside of the shutoff valve. The leaking valve is soldered on and I bought the same kind except the new one is a 14 turn valve. To remove a compression-style valve hold the valve body with an adjustable or open-end wrench or a slip-joint pliers.

Then pull the valve off the copper tubing. Drape the frame with a protection cloth and secure it to the wall. Disassemble the Shutoff Valve.

One toilet needs replacing. Use a leather glove and a damp rag to hold on and pull it out. I believe I can get away with running pipe OUTSIDE of the wall eg.

So I shut of the main valve to the house and left. Leah from See Jane Drill demonstrates how to remove an old water shut-off valve for a toilet and install a new one compression type. Open the faucet to drain the line.

Terry who sells these types of toilet valves you show if I might ask. Water Shut-off valves also called supply stop valves allow people to connect supply lines to sinks and toilets. Previous to compression piping systems around the 1980s plumbers ran copper tubing that required a torch and solder.

I need to replace it and purchased a new one. He saw what I had and did a replacement without charging me. Grabbed the bottle of spray water and spritzed both the valve still in the wrench and the pipe in the wall.

Get a soldering torch adjust it to its smallest flame and melt the solder until you can pull the valve out. Yesterday I turned the water off to the toilet while cleaning the bowl and when I finished up and turned the water back on the shut off valve started leaking pretty bad. Grab the compression nut with another wrench and turn it clockwise to loosen it.

The first is old-school soldered in place. Use a wrench or plier for loosening the nut at the other end of the valve connected to the water supply line. Flex the neoprene to try to get it supple again.

If removing a solder-type valve cut the supply line with a pipe cutter.

How Do I Get These Toilet Shut Off Valve Out Home Improvement Stack Exchange